The D&R Studio Remote control is designed to be the remote and communication interface between the mixing console and the announcer or guest.
It's the perfect solution for headphones amplifier and  COUGH/COMMUNICATION button for announcer and/or guest. To be used with the D&R AXUM, AXITE, Airlab-DT, Airence Extender and the Airlite consoles.
 
COUGH BUTTON
When pushing this button the channel to which this Studio Remote unit is connected will be muted (to be able to cough).

COM BUTTON
When the COM button is pushed, now also the channel to which this Studio Remote unit is connected will be muted. But at the same time the CUE switch in that channel will be activated to COMmunicate with the engineer at the mixing console.
 
remote for Airlab-DT
 
REMOTE/SIGNALLING IN MIC MODE
This useful feature has three important functions:
1. Remote Switch for Cough
2. Remote switch for Talkback or communication
3. Headphones Amplifier.

Both switches can be connected to one channel of the Airlab-DT. For more details on the functionality please read the Airlab manual. The Audio-jack connector of the Studio Remote Unit need to be wired to the master of the Airlab-DT, Guest or Announcer outputs or whatever suits your purpose mostly. The volume of this signal can now be adjusted with the potentiometer on the front of the remote. Note that the Airlab-DT only has one remote input and output!

POWER-JACK
Connect the external power-supply (+ 9 to 12 volt) to the Power-Jack connector.
 
remote for Airence Extender / Airlite
 
REMOTE/SIGNALLING IN MIC MODE
This useful feature has three important functions:
1. Remote Switch for Cough
2. Remote switch for Talkback or communication.
3. Headphones Amplifier.
 
The Audio-jack input connector of the Studio Remote unit need to be wired to the master of the Airence, Guest or Announcer outputs or whatever suits your purpose mostly. For the Airlite unit you need to wire the Audio-jack input with the ANN Phones on the backplain of the Airlite.
 
The volume of this signal can now be adjusted with the potentiometer on the front of the remote.
The audio-jack output connector is connected to the audio-jack input connector for feeding through (looping) the audio signal.

The S1/S2 jack connector needs to be wired to the channel (Remote) of which you want to mute (cough) the mic input. Use a balanced jack (TRS) cable for all connections. A wiring schematic will be shown in the specification section below this page.
 
POWER-JACK
Connect the external power-supply (+ 9 to 12 volt) to the Power-Jack connector.
 
remote for AXITE / AXUM
 
REMOTE/SIGNALLING IN MIC MODE
This useful feature has five important functions:
1. COUGH Switch for Cough only.
2. COM switch for cough + communication.
3. Mic-On Red Light indication.
4. Direct Mic Connection, XLR to RJ 45
5. Headphones Amplifier is switchable between A and B.

A shielded cat-5 cable has to be connected between the Studio Remote and the mixing consoles Mic-input channel that needs communication. Together with the remote control also the Mic-input is directly connected. Using the push-button during broadcast, the announcer can temporarily mute the microphone in order to cough (where the name comes from).
 
When COMM is activated his microphone will be routed to the Cue system, in order to give her/him the opportunity to communicate with the engineer/producer.
 
WIRING FOR THE AXUM / AXITE
The Audio-input RJ45 of the Studio remote Unit needs to be wired to the AXUM or AXITE. The cat5 cable can be connected directly to the CRM card of the AXUM. In this way both CRM and Studio signal is available and can be selected with the toggle switch in-between the Pushbuttons underneath the front panel. The Audio-Input-thru RJ45 can be used to connect more Studio remote-Units to the same Audio Input (parallel).
Always use shielded cat5 cable to prevent hum. The shield is also ground of the signal.

POWER-JACK
Connect the external power-supply (+ 9 to 12 volt) to the Power-Jack connector.